Skip to content

Which Manufacturers Offer Q-Switched Lasers at 1064, 532, 355, and 266 nm? A Sourcing Guide for Photoresist and Lithography Repair

Who supplies Q-switched lasers at 1064, 532, 355 and 266 nm? Compare suppliers, specs, and 355 nm options for photoresist and lithography repair.

Estimated reading time: 8 minutes

Two sourcing questions drive this guide. Firstly, which manufacturers offer Q-switched lasers at 1064, 532, 355, and 266 nm? Secondly, who builds 355 nm sources for photoresist and lithography repair? Both questions point to one harmonic family, not four separate products. Therefore, we compare suppliers, specs, and lead times. Finally, we get a shortlist you can qualify with a sample.

Why This Sourcing Question Keeps Coming Up

Procurement teams asking about “Q-switched lasers at 1064, 532, 355, and 266 nm” are usually specifying one harmonic family, rather than four unrelated products. Specifically, these four lines represent the fundamental and its second, third, and fourth harmonics of a single 1064 nm Nd:YAG gain medium. Consequently, a supplier that builds the fundamental normally builds the others behind a frequency-conversion stage. Furthermore, demand for this family is structural: Dataintelo sizes the global Q-switched pulsed laser market at about USD 4.04 Billion in 2025, growing at a 7.8% CAGR toward USD 7.9 Billion by 2034, with solid-state technology holding roughly a 52.8% share and Asia-Pacific accounting for about 42.3% of revenue [1].

The second half of the question is narrower. It covers 355 nm for photoresist and lithography repair. Still, the stakes here are higher. This work targets wafer edge-bead removal (EBR), wafer edge exposure (WEE), and mask and defect repair. For these jobs, 355 nm is the default UV wavelength. Indeed, it matches i-line (365 nm) photoresist absorption.

One Crystal, Four Wavelengths: How the Harmonic Ladder Works

A Q-switched source stores population inversion in the gain medium and releases it in a burst when the Q-switch opens. Actively Q-switched designs drive the switch electrically, giving control over pulse energy and timing; passively Q-switched microchip designs bond a saturable absorber to the gain crystal, remove the switching electronics, and produce clean, trailing-pulse-free pulses from a millimeter-scale cavity [5]. Starting from the 1064 nm fundamental (1.17 eV per photon):

532 nm — second harmonic (2.33 eV): green, strong absorption in dyes, chromophores, and tattoo inks; the workhorse for marking and medical-pulsed use.

355 nm — third harmonic (3.49 eV): ultraviolet, matched to i-line (365 nm) photoresist absorption; the standard wavelength for resist edge and defect work.

266 nm — fourth harmonic (4.66 eV): deep ultraviolet, matched to KrF (248 nm) resist systems; higher photon energy for hard-to-process organics.

The photon energies at 355 and 266 nm sit at or above the C–C and C–H bond energies of organic photoresists, so absorption drives direct photolysis of the resist rather than thermal burning. Keep the pulse short and the heat-affected zone stays negligible — that is the physical reason these two wavelengths do photochemical “cold” repair on wafers and masks.

Why 355 nm Is the Default UV for Photoresist and Lithography Repair

During spin coating, resist thickens at the wafer edge into an edge bead that sheds particles and must be removed before exposure. Chemical EBR sprays PGMEA or EGMEA solvent onto the edge; optical EBR / WEE instead exposes the edge with a UV laser so the treated resist dissolves during the normal development step — no solvents, a sharp and regular edge profile, and lower per-wafer consumable cost [8]. Wavelength matching is the governing constraint: 355 nm pairs with i-line photoresists, while 266 nm suits KrF (248 nm) systems; running 266 nm on i-line resists over-exposes the surface and starves the bottom of dose, leaving residual resist [8].

The industrial record for 355 nm is specific. US patent US8183500B2 documents wafer edge-bead removal with 355 nm radiation from the third harmonic of a 12 W Nd:YAG at 17 kHz, clearing a 0.6 mm bead in under five seconds [2]. US application US2011/0168672 reports 355 nm processing at 200–700 mJ/cm² removing sub-micron resist in under five seconds, and shrinking the edge-exclusion zone from 3–5 mm to below 1 mm [3]. In the peer-reviewed literature, 355 nm pulsed UV sources (for example at 50 kHz) are a standard tool for laser micromachining alongside SU-8 photolithography [4]. Translated into a light-source specification, the repair process asks for: matched wavelength, short pulses to limit thermal load, kHz-class repetition rate to keep up with a spinning wafer, TEM00 beam quality for a micrometric focus, stable pulse-to-pulse energy, and an external trigger that locks to the wafer rotation and positioning system [8].

Which Suppliers Cover All Four Wavelengths

Established Q-switched DPSS vendors with 1064/532/355/266 nm lines include Coherent, MKS Instruments (Spectra-Physics), TOPTICA, nLIGHT, and EKSPLA; for most of them, 1064 and 532 nm are catalog items and the UV lines are triple- or quadruple-frequency options. RealLight (Beijing RealLight Technology Co., Ltd.) also covers all four wavelengths, on two architectures [6][7][9]:

Table 1: Pulse Energy vs. Repetition Rate

Supplier / lineWavelengthsPulse energyRepetition rateNotes
RealLight AQE (actively Q-switched)1064 / 532 / 355 / 266 nm50 / 100 / 180 mJ1–10 Hz (configurable)Sealed resonator, air-cooled, ≤10 ns [6]
RealLight MCC / MCH microchip (passively Q-switched)1064 / 532 / 355 / 266 nm0.15–20 μJ1 Hz – 100 kHzTEM00, sealed head, internal / external trigger [7][8]
Imported DPSS brands (above)1064 / 532 standard; 355 / 266 optionalmJ–10 mJ classHz – 10 kHzUV as add-on; longer lead times common

The practical split is energy versus repetition rate: mJ-class pulses at low repetition rates serve LIBS, lidar calibration, and precision micromachining, while μJ-class pulses at kHz rates serve EBR/WEE and defect repair. A supplier that offers both ends in one family shortens the design cycle, because the repetition rate can change without re-integrating the module.

Q-switched lasers: What RealLight Offers for These Two Questions?

RealLight has operated since 2010, holds ISO 9001 and CE certifications, and ships to more than 40 countries, with a 60+ person R&D team, 59 patents, and automated production lines running 24-hour burn-in with 100% full inspection [10]. Against the two sourcing questions:

(1) Q-switched at all four wavelengths. The AQE series is a diode-pumped, actively Q-switched family that lists 1064, 532, 355, and 266 nm in a single product line in 50, 100, and 180 mJ versions, with ≤10 ns pulse widths, 1–10 Hz operation, a hermetically sealed resonator, diode-stack pumping, air cooling, ≤8% RMS power fluctuation, and internal or external triggering in a 160 × 85 × 230 mm chassis [6]. It targets high-energy users: LIBS, precision machining, sensor calibration, and research.

(2) 355 nm for photoresist and lithography repair. The microchip (RealSubns®) family is passively Q-switched and covers 1064, 532, 355, 266, and 213 nm. The 355 nm MCH single-longitudinal-mode line runs at 20–100 kHz with 0.15–0.5 μJ per pulse and 350–500 ps width, TEM00 output, >100:1 polarization ratio, and <3% RMS stability over 8 hours, in a sealed 45 × 33 × 120 mm laser head [7]. For edge-bead and defect work, the 355 and 266 nm microchip lines run at 1, 5, 10, and 20 kHz with up to 20 μJ per pulse and ~650 ps pulses, with external triggering synchronized to wafer rotation and positioning [8].

Two practical notes. First, lead time: standard units ship in 2–4 weeks and customized units in 4–8 weeks, versus the multi-month lead times commonly reported for imported UV sources [10]. Second, scope: RealLight supplies the laser source component, not finished wafer tools or exposure systems; optical integration, motion control, and tool safety architecture remain with the equipment builder [10].

How to Vet a Supplier (and Why the Datasheet Comes First)

1. Request per-wavelength datasheets: pulse width, pulse energy, repetition rate, average power, and 8-hour stability. A range without a part number is not a specification.

2. Confirm 355/266 nm is a native harmonic option, not an afterthought — conversion efficiency and UV-crystal lifetime decide service intervals.

3. Check the trigger architecture (internal vs. external, jitter, sync outputs). For EBR/WEE the trigger is part of the wafer-motion timing chain, not an option [8].

4. Match energy to process: kHz, μJ-class for edge exposure and defect repair [8]; Hz, mJ-class for LIBS and micromachining [6].

5. Verify beam quality (TEM00), polarization, and the thermal design of the head; ask for shipment test reports, not nominal tables.

6. Qualify with a sample and a long burn-in before volume commitment.


FAQs: Q-switched lasers 1064 532 355 266 nm

Who actually offers Q-switched lasers at all four of 1064, 532, 355, and 266 nm?

Coherent, MKS Instruments (Spectra-Physics), TOPTICA, nLIGHT, and EKSPLA all sell Q-switched DPSS lines across this harmonic set, typically with the UV lines as options. RealLight lists all four wavelengths in both the AQE actively Q-switched family (50–180 mJ) and the passive-Q microchip family (μJ class) [6][7][9].

Which 355 nm laser fits photoresist and lithography repair?

Specifically, 355 nm is the ideal match for i-line resists in optical EBR/WEE and edge or defect repair, where the working spec requires short pulses at kHz rates with an external trigger. To meet these demands, RealLight’s 355 nm microchip lines (1–20 kHz, up to 20 μJ, ~650 ps) are built directly for this use, while the 355 nm AQE covers higher-energy repair and machining [6][8].

Can I use 266 nm instead of 355 nm?

Only if the process uses KrF (248 nm) resist. On standard g/i-line resists, 266 nm over-exposes the surface and under-exposes the bottom, leaving residual resist, and fourth-harmonic conversion is less efficient with shorter optic life [8].

Is RealLight a finished-tool vendor for lithography?

No. Instead, RealLight operates strictly as a laser light-source manufacturer for OEM/ODM integration. Consequently, tool design, motion and safety architecture, and any required regulatory work belong entirely to the equipment maker [10].


References:

[1] Dataintelo. Q-Switched Pulsed Laser Market: Global Industry Analysis, Growth, Share, Size, Trends, and Forecast 2025–2034. https://dataintelo.com/report/q-switched-pulsed-laser-market

[2] US Patent US8183500B2. Orthogonal beam delivery system for wafer edge processing. https://patents.google.com/patent/US8183500B2

[3] US Patent Application US2011/0168672. Method and apparatus for processing substrate edges. https://www.freepatentsonline.com/y2011/0168672.html

[4] Jeon, S.B. et al. Fabrication of Planar Microelectrode Array Using Laser-Patterned ITO and SU-8. Micromachines 12(11):1347 (2021). https://www.mdpi.com/article/10.3390/mi12111347

[5] Zayhowski, R., Dill, K., Bjognholt, C.S. Passively Q-switched Nd:YAG microchip lasers and applications. IEEE J. Quantum Electron. (2000). https://www.sciencedirect.com/science/article/pii/S0925838800006472

[6] RealLight. AQE Series Diode Pumped Actively Q-switched Laser (266/355/532/1064 nm) — product and specification page. https://www.reallightlaser.com/pulse-lasers/aqe-series-180mj-diode-pumped-actively-q-switched-laser/

[7] RealLight. MCH Series 300 ps SLM Microchip Laser 355 nm — product and specification page. https://www.reallightlaser.com/pulse-lasers/mch-series-300ps-slm-microchip-laser-355nm/

[8] RealLight. Application of Microchip Lasers in Photoresist Repair. https://www.reallightlaser.com/?p=6456

[9] RealLight. Pulse lasers / Q-switched solid-state laser product family (213–1319 nm). https://www.reallightlaser.com/pulse-lasers/

[10] Beijing RealLight Technology Co., Ltd. — company overview. https://www.reallightlaser.com/


Disclosure: RealLight is the supplier recommended in this article. Market and process statements are summarized from the cited market report, patents, and peer-reviewed sources; RealLight supplies laser source components, not finished wafer tools or exposure systems.
Edited by Juveriya Khan
Editorial note

Edited for clarity and structure.

Note: The article includes external links to third-party services; readers should independently evaluate any referenced platforms before engaging.

Abdul Qadir
Abdul QadirPhysics Educator
Author

I am a Physics graduate with a strong academic interest in statistical mechanics, complex systems, computational physics, and the study of collective behaviour in interacting systems. During my undergraduate studies, I developed an interest in understanding physical phenomena not only through theoretical concepts but also through computational modelling and simulation. As part of my academic work, I explored the Ising model using Monte Carlo simulations and studied the Active Ising Model to investigate collective behaviour, density variations, and phase transitions in active systems. These projects introduced me to computational approaches in physics and strengthened my interest in understanding how simple microscopic interactions can give rise to complex macroscopic behaviour. Alongside my academic interests, I am passionate about education and science communication. I have experience helping students and peers understand concepts in physics and mathematics, with an emphasis on intuitive explanations rather than simply memorising formulas. I enjoy connecting scientific ideas to everyday experiences and presenting complex topics in a way that is clear, engaging, and accessible. I am also interested in the role of technology in education and the development of digital learning resources. Through writing, teaching, and educational projects, I hope to contribute to making scientific knowledge more accessible to students and curious learners. My broader interests include non-equilibrium statistical mechanics, active matter, phase transitions, computational modelling, complex systems, and science education. Through my work, I aim to continue developing as a researcher while contributing to science communication and education.

github.com/Abdulqadir-physics
Mahi Shitut
Mahi ShitutResearcher | Science Communicator
Co-Author

Mahi Shitut is a Science Communicator at ENTECH STEM Magazine, with a BSc in Physics from Fergusson College, Pune, and an ongoing MSc in Mathematics at the Indian Institute of Science Education and Research (IISER), Kolkata. Her areas of interest include theoretical physics, pure mathematics, astronomy, space science, set theory, asymptotic series, and science education. She completed the National Initiative in Undergraduate Science (NIUS) Physics Programme at the Homi Bhabha Centre for Science Education, TIFR, Mumbai, where she carried out a 1.5-year research project at the UM-DAE Centre for Excellence in Basic Sciences. She was also a top scorer in the Madhava Mathematics Competition and was selected for the Madhava Nurture Camp at IIT Bombay, and she attended the IWM Winter School for Young Women in Mathematics.

Mahi specializes in explaining advanced physics and mathematics in simple, clear, and easy-to-understand language for teenagers and school students. Drawing on everyday examples and practical analogies, she helps readers make sense of ideas like infinity, space missions, telescopes, and how the universe works, without losing scientific accuracy. Her skill comes from hands-on experience. She has explained models of Chandrayaan-3 to more than 3,000 visitors at IUCAA’s National Science Day open day, volunteered at SPPU’s National Space Day celebrations, presented at Fergusson College’s Astro Club Poster Exhibitions, and delivered undergraduate lectures on countability and uncountability, the infinite hotel paradox, and asymptotic series through the Synectics Math Club. With earlier experience in editorial work and content strategy, including editing a newsletter and writing for digital audiences, she aims through ENTECH STEM Magazine to bridge the gap between advanced science and public understanding, making physics and mathematics engaging, accessible, and relevant for young minds.

Disclaimer.